Professional Canon EOS 650D (Rebel T4i) Repair
Why Choose Us for Canon 650D Repair
We fix what others couldn’t — or can’t.
Same-Day Repair
Original Parts
1–3 Month Warranty
Professional Team
Canon EOS 650D Service Prices
Prices exclude parts. We prefer component-level repair when viable. Same-day express available. Every camera gets full inbound and outbound testing with a written warranty.
- Diagnostics – $0 if approved / $50 if declined
- Express repair (same day) – +50% to selected service
- No power / random shutdowns (power rails, fuses, DC-DC) – from $165
- Vari-angle rear LCD assembly (3.0″) – from $140 (incl. hinge ribbon)
- Touch panel / digitizer – from $120
- Shutter assembly – from $210
- Mirror box / sub-mirror alignment – from $140
- AF unit cleaning + calibration – from $115
- Lens communication (Err 01) path service – from $95
- Pop-up flash repair (Err 05 / “BUSY”) – from $100
- Hot shoe contacts / sync circuit rework – from $85
- SD slot pin repair (SDHC/SDXC, UHS-I) – from $100
- USB 2.0 (Mini-B) port – from $95
- HDMI (Mini, Type C) port – from $110
- Mode dial / buttons service – from $90
- Mic jack board (hiss / one channel dead) – from $110
- Sticky grip rubber replacement – from $85
- Door seals & light-trap refresh – from $70
- APS-C sensor cleaning (wet swab + dust map) – from $55
- Body deep clean (ports + exterior) – from $50
- Battery door / latch (LP-E8) – from $70
- Main board / power regulation repair – from $175
- Firmware recovery / stuck on logo – from $85
- Lens mount & bayonet service (EF/EF-S) – from $115
Final pricing depends on fault severity and parts availability. Your camera is returned fully tested with documentation.
Typical Issues We Fix
- Camera won’t power on or shuts off under load — DC-DC, fuses, or rails; isolate and repair.
- Touchscreen ghost taps / dead zones — failed digitizer or flex; replace and recalibrate.
- Vari-angle LCD blanks or flickers at certain angles — hinge ribbon fracture; swap assembly.
- Err 01 with EF/EF-S lenses — oxidized contacts or torn mount flex; rework or replace.
- “Recording has stopped automatically” — slow SD or thermal limit; media and thermal service.
- Pop-up flash stuck / Err 05 / “BUSY” — hot-shoe microswitch jam or weak driver; free and repair.
EOS DSLRs — Error Codes Quick Hints
| Code | Meaning | First Aid |
|---|---|---|
| Err 20 | Mechanical fault | Power cycle; reseat battery/lens; service mirror/shutter if repeats. |
| Err 30 | Shutter problem | Try fresh LP-E8; inspect blades; likely shutter replacement. |
| Err 40 | Power/electrical | Clean contacts; avoid hot-plug; board diagnostics. |
| Err 70 | Data/processing | Reset; new SD card; firmware/board service if persistent. |
| Err 80/99 | General/image fault | Stop use; full diagnostics to isolate shutter/sensor/firmware path. |
Pro Tips for EOS 650D
- Use SDHC/SDXC UHS-I; V30 recommended for video. Avoid microSD adapters.
- Remove screen protectors when diagnosing touch drift; if it persists, service the panel.
- Protect the swivel hinge in cold weather; ribbon cracks are common.
- Keep hot-shoe rails clean; a stuck microswitch disables the pop-up flash.
- If OVF focus differs from Live View, book AF unit calibration.
FAQ – Canon EOS 650D
1. The camera registers touches by itself.
We replace the digitizer, inspect the flex, reseat connectors, and calibrate.
2. LCD only works at certain angles.
The hinge ribbon is fractured. We swap the display assembly and reseal the hinge.
3. Pop-up flash shows Err 05 or “BUSY”.
We free the hot-shoe microswitch, service the pop-up unit, and verify driver/cap charge timing.
4. Err 01 with certain EF/EF-S lenses.
We rework contacts, check the mount flex and iris lines, and test with reference lenses.
5. Sticky or discolored grip.
We remove degraded rubber, deep-clean the surface, and install new grip pieces.
6. Stuck on logo / boot loop.
Service-level reflash, boot partition checks, and NAND integrity test.