Fujifilm Repair

Prices exclude spare parts. We service X-Series APS-C and GFX medium format bodies, plus XF, XC, and GF lenses. Component-level repair whenever possible.

• Diagnostics – $0 if repair is completed / $50 if declined
• Express repair (2-3 hours) – +50% to the selected service
• Shutter replacement – from $110
• Sensor cleaning (APS-C/GFX, dry & wet + dust map) – from $85
• Sensor replacement – from $200
• X-Mount / G-Mount bayonet – from $95
• USB-C / micro-HDMI / DC-in ports – from $75
• IBIS unit service (X-H1/X-T4/X-S10/X-H2S) – from $150
• OIS module service (lens) – from $140
• Aperture/diaphragm unit – from $130
• LCD or EVF module – from $110
• Main board and firmware recovery – from $170
• SD UHS-II or CFexpress Type B slot pins – from $110
• Lens calibration and optical alignment – from $70

Final cost depends on the Fujifilm model and repair complexity. Each service includes testing and a written warranty.

What We Do Best

• X-Series bodies: X-T, X-H, X-S, X-Pro, X-E. GFX 50 and 100 series medium format.
• Fujinon XF, XC, and GF lenses: LM/DC AF motors, diaphragm, flex and encoder repairs.
• X100 series fixed-lens service: leaf shutter, ND module, and full lens assembly replacement.
• Water and saltwater recovery, corrosion cleanup, gasket and seal renewal, data recovery.

Typical Fujifilm Issues We Fix

• “Turn off the camera and turn on again” after shutter or aperture faults.
• “Lens control error” or “Lens not attached” due to contact block or mount tolerance.
• X100 series: sticky aperture, leaf shutter stiction, ND filter anomalies, dust behind front group.
• IBIS micro-jitter or rattle on startup; blur on tripod when stabilization stays on.
• OIS rattle or image jump in zooms and fast primes.
• X-Trans sensor dust or oil spots; streaks after DIY cleaning.
• “Card not initialized” or slow buffer; bent pins or fatigued SD/CFexpress slots.
• HDMI handshake issues with recorders; loose or damaged ports.
• AF inconsistency in low light or with linear motors; calibration and firmware alignment.
• Banding under LED when using electronic shutter; EFCS or flicker reduction setup required.

Flashes & Accessories

We service EF-X flashes, hot-shoe connectors, battery grips, and USB-C power accessories: board-level repairs, cracked feet, sync faults, firmware updates.

1. Do you calibrate XF, XC, and GF lenses?

Yes. We align focus groups, verify flange distance, tune AF motors, and check OIS centering and communication.

2. X100 series overexposes or shows shutter errors. Fixable?

We rebuild or replace the integrated leaf shutter, aperture, and ND module, then re-collimate the lens assembly.

3. Safe sensor cleaning for X-Trans and GFX?

Use a hand blower first. We provide wet cleaning with the correct swab size, edge cleanup, and a dust map at f/16.

4. My camera shows “Turn off and on again”. What do you check?

Shutter and aperture paths, power rails, and firmware. We replace worn parts and run a full functional test.

5. IBIS blur on tripod. Should I disable it?

Yes on rigid support. If blur persists with IBIS off, we test the module, lens mount, and sensor seating.

6. Which cards are best for X-H2S and GFX100 series?

Use CFexpress Type B for high-bitrate video and bursts. For SD slots, choose UHS-II V90, format in camera, and avoid removal while writing.

7. HDMI drops out with my recorder. Can you fix that?

We replace the HDMI port, validate signal stability, and recommend right-angle adapters and cage-based strain relief.

8. AF misses with adapted lenses. Can calibration help?

We check adapter tolerance, adjust flange distance, and tune AF where supported. We also test focus consistency across distances.

9. Can you remap hot pixels for long exposures or astro?

Yes. We perform pixel remapping, verify sensor temps, and advise Long Exposure NR and stable power for multi-minute shots.

10. Rolling shutter banding under LED lights. Any fix?

Use mechanical or EFCS, enable flicker reduction, or set shutter speeds that match the light frequency. We can profile your lighting.

11. Water or saltwater exposure. What is the first step?

Power off, remove battery and card, do not dry with heat, seal with desiccant, and bring it the same day. We neutralize and stop corrosion.

12. Turnaround and warranty?

Standard 3-5 business days. Express 2-3 hours when parts allow. Written warranty 1-3 months by job type.